This is a hack I have done on the AR3000 scanner My one is a first series one, but I guess the 3000A has the
very same motherboard, so it should apply to the new one too One defect I've found of this scanner is that
its audio completely lacks basses in the AM/NFM/SSB/CW modes I've gone to the service manual, and I've found
that this is intentional The audio line passes through a notch filter This is stated to be 300-3000Hz I do
not believe much to the upper limit (the 5Khz whistle on shortwaves is quite strong), but I find the lower
one annoying and unjustified Therefore I removed that cutoff After the intervention, I find a much improved
audio quality, both in speech and in broadcast, and I haven't yet found a signal which makes me regret it.
And if I even wanted, now I can add an external equalizer The mod itself is simple, but involves working on
SMD, so it's quite DELICATE Do it at your risk I'd reccommend having a copy of the PC layouts and of the
schematics from the service manual, in order to understand what you're doing I found useful making a
coloured xerox copy of the etch layouts on transparencies, so to overlay them Theory:the notch filter for
AM/NFM/CW/SSB is built around the double op-amps in IC7-IC8 on the if/audio board The lower cutoff is
determined primarily by R130(10k), R139(4.7k), C130(22n), C131(22n), C137(22n) (I don't swear on the
correctness of the identifiers since my schematic is borderline readable) C128 ,---||--- |-/\/\/\-|
,________ | R143 | | | | |\ | | |\ | ---|-\ | C130 C131 R139 | 2| \ | R142 2|
\___|____||____||____/\/\/\_|__|- \__|___/\/\/\_ | /1 || | || | | /1 ---|+/ / |___||_____|+/ 3|/ R \ || | 3|/
1 / C137 | IC8 3 \ _______| IC7 0 / | _ = What I did was:to remove R130; to solder a 0.1uF condenser in
parallel to C130+C131; to remove C137 and to shunt it with a jumper Operation:unscrew the cover and nake
the receiver Unplug the loudspeaker connector The audio/if board is the lowest one, and has to be unscrewed
and turned upside-down, so that the SMD side is accessible To this extent, at least one of the coax
connectors (J1,J10) has to be unplugged Locate the components to be attacked (again I recommend having the
etch layout; I try to sketch, but it's not as clear) The region is on the SMD side opposite to IC9 on the
component side IC9 is recognizable since is a voltage regulator, it has 3 pins and gets hot ^^^^^^^^
(ceramic filters) (components side) __ / \ || ||=|| || (hole) \__/ || || C131 22k IC7 || || C130 100k || ||
|| || || || ||=|| || || 220p || || R130 ||C137|| IC8 || || || || || || 220p || ( IC 11 ) (components side)
vvvvvvvv (Sorry but I can't draw any better) I suggest to turn the radio on, and to try to shunt C130+C131
and C137 leaning a O.1uF condenser on the proper tin points, in order to locate them The sound should get
richer of basses in both cases Then unsolder R130 and C137 It requires a quick and firm hand since the
components are ~4mm long, and glued to the board Solder a short shunt in place of C137 Solder a 0.1uF
condenser (or greater) on the extremes of C130+C131 A little ceramic one does it; even if it is not as neat
as replacing with another SMD, there is plenty of room I did all the job with no other equipment than a
cheap and thin tip soldering iron and a pair of pincers, but, again, entirely YOUR RESPONSIBILITY Rescrew,
close, enjoy.. Of course the effect is much better with an external speaker I'd like to hear comments or to
know if anyone has tried other hacks on the same box Please email me Once more, I take NO RESPONSIBILITY
whatsoever.. :) .. In my case it worked well, though A final note:I'm indebted to Henry Laviers
, who sent me a copy of the service manual two years ago Enrico Segre, segre@polito.it
Source QRZ: The Windows Ham Radio CDROM |
